Final Exam for ch 1-10
46
Which Windows tool should be run before upgrading the operating system?
#Ntbackup
47
The technician has been asked to upgrade the printer driver for an old printer. What is the best source for a new driver?
#manufacturer's website
48
Where can a user change the idle time after which a laptop will switch to standby mode?
#Left-click Start > Control Panel > Power Options, then click the Power Schemes tab.
49
A home computer owner has a PC system that runs Windows XP. For security reasons the owner has been using a limited local user account for a number of years. The owner wishes to install a new piece of software, but the user account does not have the necessary permissions. Which type of account does the owner need to use to install the new software?
#administrator
50
A student enables file sharing on a laptop so that a friend can access music files. Which type of service is being configured?
#peer-to-peer
51
What do the terms refresh rate, interlace, and aspect ratio explain?
#image properties of a monitor
52
A technician wishes to boot a computer using a CD-ROM that contains a limited operating system and diagnostic utilities. Where would the technician set the boot order for the PC?
#BIOS
1
A computer user buys a low priced replacement monitor but finds that there is a lot of flicker. The flicker makes the monitor unusable. Which characteristic of a monitor needs to be considered to ensure flicker-free viewing?
#refresh rate
2
When analyzing a protocol used on the network, it is discovered that multicast messages are being sent to network devices. Which class of IP addressing is being used to send these messages?
#D
3
A technician notices that a data floppy disk is in the floppy disk drive of a computer when it is powered on. Which error message could this potentially cause?
#invalid system disk
4
What characterizes spoofing?
#Making data appear to come from a source other than the actual source.
5
When a Windows XP computer has completed the POST for each adapter card that has a BIOS, what is the next step during the boot sequence?
#BIOS reads the MBR.
6
When calculating the total cost of ownership of a printer it is necessary to consider the cost of the consumables. Which two consumables are associated with an inkjet printer? (Choose two.)
#ink cartridge
#paper
7
Which protocol adds security to remote connections?
#SSH
8
What is the purpose of an IRQ?
#Request information from the CPU.
9
A wireless LAN is being deployed inside the new park ranger, one room office that is located at the highest part of the national park. When the testing was completed, the technicians reported that occasionally, the wireless LAN signal is affected by some type of interference. What are two possible causes of the signal distortion? (Choose two.)
#the number of wireless devices that are used in the wireless LAN
#the large number of trees that surround the office
10
When installing a service pack or security patches on an operating system, what should be done to protect the system in the event of a faulty or aborted installation?
#Create a restore point.
11
A technician is asked to wire a network that supports CSMA/CD. Which architecture and physical topology should the technician use for supporting this access control method?
#Ethernet and Star
12
What is the best way to fully ensure that data is unable to be recovered from a hard drive?
#shattering the hard drive platters with a hammer
13
A technician is asked to configure the time the system must be idle before the hard disk spins down on all the Windows-based laptops in the company. The technician configured the power options in Windows but it appears to have no effect. Where should the technician look to enable power management?
#System Registry
14
A printer has a paper jam. An impatient user has sent multiple print jobs of the same document to this printer. What can be done to remove these print jobs?
#Cancel the jobs in the printer queue.
15
ABC Inc. decided to integrate redundancy by connecting multiple hard disks to duplicate the information they store. Which type of adapter will need to be installed on the servers to accomplish the desired redundancy?
#RAID adapter
16
A call center technician has asked a customer to perform a simple operation to fix a problem on a computer. The customer seems unable to perform the task. What should the technician do?
#Determine whether the customer would prefer to receive the instructions in another form, such as e-mailed, illustrated written instructions.
17
Which two technologies enable printers to be accessed by multiple network users? (Choose two.)
#Wi-Fi
#Ethernet
18
A user reports that a printer is printing unknown characters on documents. What is a possible solution to this issue?
#Uninstall and reinstall the printer driver.
19
Which network device uses a MAC address table to segment the network?
#router
20
A technician needs to configure the hard drive on a computer so that there appears to be one drive for the operating system and four drives for data from different applications. How can the hard drive be configured to provide this perception?
#Create one primary partition and one logical partition with four logical drives within it.
21
A supervisor received a complaint that one of the technicians was rude and disrespectful. Which action by the technician most likely caused the customer to complain?
#The technician interrupted a number of times to ask questions.
22
A technician is troubleshooting a user complaint that a printer is not printing a report. Which step is one of the first that the technician should take?
#Check the Device Manager on the user computer for hardware problems.
23
Which Registry file contains information about all software that is installed on a Windows XP computer?
#HKEY_LOCAL_MACHINE
24
A hacker is detected using commonly available wireless hacking tools to access encrypted wireless network communication. Which resolution would prevent this action?
#Change the SSID that is being used on the wireless network.
25
Which two general precautions should be taken before replacing any non-hot-swappable laptop component? (Choose two.)
#Disconnect the power cord.
#Remove any batteries.
26
Which power mode should be used by a laptop so that all the data is saved, all the applications the user was working on are left open, and there is no power used by the laptop?
#Hibernate
27
What is the purpose of SCSI and RAID adapters?
#to connect storage devices such as hard disk drives to a PC
28
Which network protocol is used to automatically assign an IP address to a computer on a network?
#DHCP
29
A customer used the convert.exe utility to take advantage of NTFS security features. The customer later discovered that the application on the computer can only read FAT32 files. After the hard drive was formatted back to FAT32, the customer noticed all of the data files are missing. What should the customer do next?
#Restore the data files that were backed up in preparation for the conversion.
30
Which two components normally require a laptop to be powered down and the battery removed before removing the components? (Choose two.)
#internal hard drive
#RAM
31
A customer reports that after using a computer for over a year, the computer now takes more time to access the files. Which management tool can be used first, before any other complex procedure?
#defrag
32
A customer needs to purchase a new power supply for a computer. What must be considered when selecting an appropriate power supply?
#The power supply has sufficient wattage to support all components inside the computer.
33
What is a benefit of using the USB or FireWire ports to connect peripherals to a laptop?
#The peripherals can be plugged in and out without turning the laptop off.
34
A small business has used a high quality configurable flatbed scanner to scan a number of photographs to print as large posters. However, the quality of the images printed as posters is poor. What should the user do?
#Increase the resolution of the scanner.
35
A user has been writing data to a USB flash memory drive. What should the user do before removing the device?
#Click on the Safely Remove Hardware icon in the system tray then on the device.
36
A technician installed a network adapter in a computer and wants to test network connectivity. The ping command can only receive a response from local workstations. What could be causing the problem?
#The default gateway is not set.
37
A technician is explaining the differences between inkjet printers and laser printers to a customer. Which two comparisons should the technician make? (Choose two.)
#Inkjet printers are less expensive than laser printers.
#The laser printer output is dry after printing, but an inkjet printer may still have wet ink on the paper after printing.
38
A network administrator is troubleshooting a server that keeps crashing. While monitoring traffic to the server, the administrator notices repeated, larger than normal pings to the server. What is the name of this type of attack?
#ping of death
39
A technician wants to create a new partition on a new additional hard drive. Which tool should be used?
#Disk Management
40
Which two quick solutions are commonly recommended when a technician is troubleshooting a laptop? (Choose two.)
#Reboot the laptop.
#Disconnect the peripherals.
41
A company uses a single computer to receive and test all Windows updates. When the most recent update was installed, several programs failed. What is the first course of action that a technician should attempt to remove the update?
#Run a System Restore from the last restore point.
42
A mobile training room uses a generator to power the PCs, servers, and printers. The company that runs the room upgraded the equipment but then found that when all the devices are powered up they become unreliable, with some PCs shutting down. What may cause this power problem?
#The power consumption of all devices is too much for the electrical circuit that is provided.
43
When installing the Windows XP operating system, a technician is given a choice of file systems to use. If security is a requirement, which file system should be chosen?
#NTFS
44
A technician has replaced a failing floppy drive. While testing the new drive, the technician notices that the floppy drive light remains lit constantly. What is most likely the cause of the problem?
#The ribbon cable is installed incorrectly.
45
Which two types of connectors can be found on DVI cables? (Choose two.)
A computer user buys a low priced replacement monitor but finds that there is a lot of flicker. The flicker makes the monitor unusable. Which characteristic of a monitor needs to be considered to ensure flicker-free viewing?
#refresh rate
2
When analyzing a protocol used on the network, it is discovered that multicast messages are being sent to network devices. Which class of IP addressing is being used to send these messages?
#D
3
A technician notices that a data floppy disk is in the floppy disk drive of a computer when it is powered on. Which error message could this potentially cause?
#invalid system disk
4
What characterizes spoofing?
#Making data appear to come from a source other than the actual source.
5
When a Windows XP computer has completed the POST for each adapter card that has a BIOS, what is the next step during the boot sequence?
#BIOS reads the MBR.
6
When calculating the total cost of ownership of a printer it is necessary to consider the cost of the consumables. Which two consumables are associated with an inkjet printer? (Choose two.)
#ink cartridge
#paper
7
Which protocol adds security to remote connections?
#SSH
8
What is the purpose of an IRQ?
#Request information from the CPU.
9
A wireless LAN is being deployed inside the new park ranger, one room office that is located at the highest part of the national park. When the testing was completed, the technicians reported that occasionally, the wireless LAN signal is affected by some type of interference. What are two possible causes of the signal distortion? (Choose two.)
#the number of wireless devices that are used in the wireless LAN
#the large number of trees that surround the office
10
When installing a service pack or security patches on an operating system, what should be done to protect the system in the event of a faulty or aborted installation?
#Create a restore point.
11
A technician is asked to wire a network that supports CSMA/CD. Which architecture and physical topology should the technician use for supporting this access control method?
#Ethernet and Star
12
What is the best way to fully ensure that data is unable to be recovered from a hard drive?
#shattering the hard drive platters with a hammer
13
A technician is asked to configure the time the system must be idle before the hard disk spins down on all the Windows-based laptops in the company. The technician configured the power options in Windows but it appears to have no effect. Where should the technician look to enable power management?
#System Registry
14
A printer has a paper jam. An impatient user has sent multiple print jobs of the same document to this printer. What can be done to remove these print jobs?
#Cancel the jobs in the printer queue.
15
ABC Inc. decided to integrate redundancy by connecting multiple hard disks to duplicate the information they store. Which type of adapter will need to be installed on the servers to accomplish the desired redundancy?
#RAID adapter
16
A call center technician has asked a customer to perform a simple operation to fix a problem on a computer. The customer seems unable to perform the task. What should the technician do?
#Determine whether the customer would prefer to receive the instructions in another form, such as e-mailed, illustrated written instructions.
17
Which two technologies enable printers to be accessed by multiple network users? (Choose two.)
#Wi-Fi
#Ethernet
18
A user reports that a printer is printing unknown characters on documents. What is a possible solution to this issue?
#Uninstall and reinstall the printer driver.
19
Which network device uses a MAC address table to segment the network?
#router
20
A technician needs to configure the hard drive on a computer so that there appears to be one drive for the operating system and four drives for data from different applications. How can the hard drive be configured to provide this perception?
#Create one primary partition and one logical partition with four logical drives within it.
21
A supervisor received a complaint that one of the technicians was rude and disrespectful. Which action by the technician most likely caused the customer to complain?
#The technician interrupted a number of times to ask questions.
22
A technician is troubleshooting a user complaint that a printer is not printing a report. Which step is one of the first that the technician should take?
#Check the Device Manager on the user computer for hardware problems.
23
Which Registry file contains information about all software that is installed on a Windows XP computer?
#HKEY_LOCAL_MACHINE
24
A hacker is detected using commonly available wireless hacking tools to access encrypted wireless network communication. Which resolution would prevent this action?
#Change the SSID that is being used on the wireless network.
25
Which two general precautions should be taken before replacing any non-hot-swappable laptop component? (Choose two.)
#Disconnect the power cord.
#Remove any batteries.
26
Which power mode should be used by a laptop so that all the data is saved, all the applications the user was working on are left open, and there is no power used by the laptop?
#Hibernate
27
What is the purpose of SCSI and RAID adapters?
#to connect storage devices such as hard disk drives to a PC
28
Which network protocol is used to automatically assign an IP address to a computer on a network?
#DHCP
29
A customer used the convert.exe utility to take advantage of NTFS security features. The customer later discovered that the application on the computer can only read FAT32 files. After the hard drive was formatted back to FAT32, the customer noticed all of the data files are missing. What should the customer do next?
#Restore the data files that were backed up in preparation for the conversion.
30
Which two components normally require a laptop to be powered down and the battery removed before removing the components? (Choose two.)
#internal hard drive
#RAM
31
A customer reports that after using a computer for over a year, the computer now takes more time to access the files. Which management tool can be used first, before any other complex procedure?
#defrag
32
A customer needs to purchase a new power supply for a computer. What must be considered when selecting an appropriate power supply?
#The power supply has sufficient wattage to support all components inside the computer.
33
What is a benefit of using the USB or FireWire ports to connect peripherals to a laptop?
#The peripherals can be plugged in and out without turning the laptop off.
34
A small business has used a high quality configurable flatbed scanner to scan a number of photographs to print as large posters. However, the quality of the images printed as posters is poor. What should the user do?
#Increase the resolution of the scanner.
35
A user has been writing data to a USB flash memory drive. What should the user do before removing the device?
#Click on the Safely Remove Hardware icon in the system tray then on the device.
36
A technician installed a network adapter in a computer and wants to test network connectivity. The ping command can only receive a response from local workstations. What could be causing the problem?
#The default gateway is not set.
37
A technician is explaining the differences between inkjet printers and laser printers to a customer. Which two comparisons should the technician make? (Choose two.)
#Inkjet printers are less expensive than laser printers.
#The laser printer output is dry after printing, but an inkjet printer may still have wet ink on the paper after printing.
38
A network administrator is troubleshooting a server that keeps crashing. While monitoring traffic to the server, the administrator notices repeated, larger than normal pings to the server. What is the name of this type of attack?
#ping of death
39
A technician wants to create a new partition on a new additional hard drive. Which tool should be used?
#Disk Management
40
Which two quick solutions are commonly recommended when a technician is troubleshooting a laptop? (Choose two.)
#Reboot the laptop.
#Disconnect the peripherals.
41
A company uses a single computer to receive and test all Windows updates. When the most recent update was installed, several programs failed. What is the first course of action that a technician should attempt to remove the update?
#Run a System Restore from the last restore point.
42
A mobile training room uses a generator to power the PCs, servers, and printers. The company that runs the room upgraded the equipment but then found that when all the devices are powered up they become unreliable, with some PCs shutting down. What may cause this power problem?
#The power consumption of all devices is too much for the electrical circuit that is provided.
43
When installing the Windows XP operating system, a technician is given a choice of file systems to use. If security is a requirement, which file system should be chosen?
#NTFS
44
A technician has replaced a failing floppy drive. While testing the new drive, the technician notices that the floppy drive light remains lit constantly. What is most likely the cause of the problem?
#The ribbon cable is installed incorrectly.
45
Which two types of connectors can be found on DVI cables? (Choose two.)
46
Which Windows tool should be run before upgrading the operating system?
#Ntbackup
47
The technician has been asked to upgrade the printer driver for an old printer. What is the best source for a new driver?
#manufacturer's website
48
Where can a user change the idle time after which a laptop will switch to standby mode?
#Left-click Start > Control Panel > Power Options, then click the Power Schemes tab.
49
A home computer owner has a PC system that runs Windows XP. For security reasons the owner has been using a limited local user account for a number of years. The owner wishes to install a new piece of software, but the user account does not have the necessary permissions. Which type of account does the owner need to use to install the new software?
#administrator
50
A student enables file sharing on a laptop so that a friend can access music files. Which type of service is being configured?
#peer-to-peer
51
What do the terms refresh rate, interlace, and aspect ratio explain?
#image properties of a monitor
52
A technician wishes to boot a computer using a CD-ROM that contains a limited operating system and diagnostic utilities. Where would the technician set the boot order for the PC?
#BIOS
1
A computer user buys a low priced replacement monitor but finds that there is a lot of flicker. The flicker makes the monitor unusable. Which characteristic of a monitor needs to be considered to ensure flicker-free viewing?
#refresh rate
2
When analyzing a protocol used on the network, it is discovered that multicast messages are being sent to network devices. Which class of IP addressing is being used to send these messages?
#D
3
A technician notices that a data floppy disk is in the floppy disk drive of a computer when it is powered on. Which error message could this potentially cause?
#invalid system disk
4
What characterizes spoofing?
#Making data appear to come from a source other than the actual source.
5
When a Windows XP computer has completed the POST for each adapter card that has a BIOS, what is the next step during the boot sequence?
#BIOS reads the MBR.
6
When calculating the total cost of ownership of a printer it is necessary to consider the cost of the consumables. Which two consumables are associated with an inkjet printer? (Choose two.)
#ink cartridge
#paper
7
Which protocol adds security to remote connections?
#SSH
8
What is the purpose of an IRQ?
#Request information from the CPU.
9
A wireless LAN is being deployed inside the new park ranger, one room office that is located at the highest part of the national park. When the testing was completed, the technicians reported that occasionally, the wireless LAN signal is affected by some type of interference. What are two possible causes of the signal distortion? (Choose two.)
#the number of wireless devices that are used in the wireless LAN
#the large number of trees that surround the office
10
When installing a service pack or security patches on an operating system, what should be done to protect the system in the event of a faulty or aborted installation?
#Create a restore point.
11
A technician is asked to wire a network that supports CSMA/CD. Which architecture and physical topology should the technician use for supporting this access control method?
#Ethernet and Star
12
What is the best way to fully ensure that data is unable to be recovered from a hard drive?
#shattering the hard drive platters with a hammer
13
A technician is asked to configure the time the system must be idle before the hard disk spins down on all the Windows-based laptops in the company. The technician configured the power options in Windows but it appears to have no effect. Where should the technician look to enable power management?
#System Registry
14
A printer has a paper jam. An impatient user has sent multiple print jobs of the same document to this printer. What can be done to remove these print jobs?
#Cancel the jobs in the printer queue.
15
ABC Inc. decided to integrate redundancy by connecting multiple hard disks to duplicate the information they store. Which type of adapter will need to be installed on the servers to accomplish the desired redundancy?
#RAID adapter
16
A call center technician has asked a customer to perform a simple operation to fix a problem on a computer. The customer seems unable to perform the task. What should the technician do?
#Determine whether the customer would prefer to receive the instructions in another form, such as e-mailed, illustrated written instructions.
17
Which two technologies enable printers to be accessed by multiple network users? (Choose two.)
#Wi-Fi
#Ethernet
18
A user reports that a printer is printing unknown characters on documents. What is a possible solution to this issue?
#Uninstall and reinstall the printer driver.
19
Which network device uses a MAC address table to segment the network?
#router
20
A technician needs to configure the hard drive on a computer so that there appears to be one drive for the operating system and four drives for data from different applications. How can the hard drive be configured to provide this perception?
#Create one primary partition and one logical partition with four logical drives within it.
21
A supervisor received a complaint that one of the technicians was rude and disrespectful. Which action by the technician most likely caused the customer to complain?
#The technician interrupted a number of times to ask questions.
22
A technician is troubleshooting a user complaint that a printer is not printing a report. Which step is one of the first that the technician should take?
#Check the Device Manager on the user computer for hardware problems.
23
Which Registry file contains information about all software that is installed on a Windows XP computer?
#HKEY_LOCAL_MACHINE
24
A hacker is detected using commonly available wireless hacking tools to access encrypted wireless network communication. Which resolution would prevent this action?
#Change the SSID that is being used on the wireless network.
25
Which two general precautions should be taken before replacing any non-hot-swappable laptop component? (Choose two.)
#Disconnect the power cord.
#Remove any batteries.
26
Which power mode should be used by a laptop so that all the data is saved, all the applications the user was working on are left open, and there is no power used by the laptop?
#Hibernate
27
What is the purpose of SCSI and RAID adapters?
#to connect storage devices such as hard disk drives to a PC
28
Which network protocol is used to automatically assign an IP address to a computer on a network?
#DHCP
29
A customer used the convert.exe utility to take advantage of NTFS security features. The customer later discovered that the application on the computer can only read FAT32 files. After the hard drive was formatted back to FAT32, the customer noticed all of the data files are missing. What should the customer do next?
#Restore the data files that were backed up in preparation for the conversion.
30
Which two components normally require a laptop to be powered down and the battery removed before removing the components? (Choose two.)
#internal hard drive
#RAM
31
A customer reports that after using a computer for over a year, the computer now takes more time to access the files. Which management tool can be used first, before any other complex procedure?
#defrag
32
A customer needs to purchase a new power supply for a computer. What must be considered when selecting an appropriate power supply?
#The power supply has sufficient wattage to support all components inside the computer.
33
What is a benefit of using the USB or FireWire ports to connect peripherals to a laptop?
#The peripherals can be plugged in and out without turning the laptop off.
34
A small business has used a high quality configurable flatbed scanner to scan a number of photographs to print as large posters. However, the quality of the images printed as posters is poor. What should the user do?
#Increase the resolution of the scanner.
35
A user has been writing data to a USB flash memory drive. What should the user do before removing the device?
#Click on the Safely Remove Hardware icon in the system tray then on the device.
36
A technician installed a network adapter in a computer and wants to test network connectivity. The ping command can only receive a response from local workstations. What could be causing the problem?
#The default gateway is not set.
37
A technician is explaining the differences between inkjet printers and laser printers to a customer. Which two comparisons should the technician make? (Choose two.)
#Inkjet printers are less expensive than laser printers.
#The laser printer output is dry after printing, but an inkjet printer may still have wet ink on the paper after printing.
38
A network administrator is troubleshooting a server that keeps crashing. While monitoring traffic to the server, the administrator notices repeated, larger than normal pings to the server. What is the name of this type of attack?
#ping of death
39
A technician wants to create a new partition on a new additional hard drive. Which tool should be used?
#Disk Management
40
Which two quick solutions are commonly recommended when a technician is troubleshooting a laptop? (Choose two.)
#Reboot the laptop.
#Disconnect the peripherals.
41
A company uses a single computer to receive and test all Windows updates. When the most recent update was installed, several programs failed. What is the first course of action that a technician should attempt to remove the update?
#Run a System Restore from the last restore point.
42
A mobile training room uses a generator to power the PCs, servers, and printers. The company that runs the room upgraded the equipment but then found that when all the devices are powered up they become unreliable, with some PCs shutting down. What may cause this power problem?
#The power consumption of all devices is too much for the electrical circuit that is provided.
43
When installing the Windows XP operating system, a technician is given a choice of file systems to use. If security is a requirement, which file system should be chosen?
#NTFS
44
A technician has replaced a failing floppy drive. While testing the new drive, the technician notices that the floppy drive light remains lit constantly. What is most likely the cause of the problem?
#The ribbon cable is installed incorrectly.
45
Which two types of connectors can be found on DVI cables? (Choose two.)
46
Which Windows tool should be run before upgrading the operating system?
#Ntbackup
47
The technician has been asked to upgrade the printer driver for an old printer. What is the best source for a new driver?
#manufacturer's website
48
Where can a user change the idle time after which a laptop will switch to standby mode?
#Left-click Start > Control Panel > Power Options, then click the Power Schemes tab.
49
A home computer owner has a PC system that runs Windows XP. For security reasons the owner has been using a limited local user account for a number of years. The owner wishes to install a new piece of software, but the user account does not have the necessary permissions. Which type of account does the owner need to use to install the new software?
#administrator
50
A student enables file sharing on a laptop so that a friend can access music files. Which type of service is being configured?
#peer-to-peer
51
What do the terms refresh rate, interlace, and aspect ratio explain?
#image properties of a monitor
52
A technician wishes to boot a computer using a CD-ROM that contains a limited operating system and diagnostic utilities. Where would the technician set the boot order for the PC?
#BIOS
A computer user buys a low priced replacement monitor but finds that there is a lot of flicker. The flicker makes the monitor unusable. Which characteristic of a monitor needs to be considered to ensure flicker-free viewing?
#refresh rate
2
When analyzing a protocol used on the network, it is discovered that multicast messages are being sent to network devices. Which class of IP addressing is being used to send these messages?
#D
3
A technician notices that a data floppy disk is in the floppy disk drive of a computer when it is powered on. Which error message could this potentially cause?
#invalid system disk
4
What characterizes spoofing?
#Making data appear to come from a source other than the actual source.
5
When a Windows XP computer has completed the POST for each adapter card that has a BIOS, what is the next step during the boot sequence?
#BIOS reads the MBR.
6
When calculating the total cost of ownership of a printer it is necessary to consider the cost of the consumables. Which two consumables are associated with an inkjet printer? (Choose two.)
#ink cartridge
#paper
7
Which protocol adds security to remote connections?
#SSH
8
What is the purpose of an IRQ?
#Request information from the CPU.
9
A wireless LAN is being deployed inside the new park ranger, one room office that is located at the highest part of the national park. When the testing was completed, the technicians reported that occasionally, the wireless LAN signal is affected by some type of interference. What are two possible causes of the signal distortion? (Choose two.)
#the number of wireless devices that are used in the wireless LAN
#the large number of trees that surround the office
10
When installing a service pack or security patches on an operating system, what should be done to protect the system in the event of a faulty or aborted installation?
#Create a restore point.
11
A technician is asked to wire a network that supports CSMA/CD. Which architecture and physical topology should the technician use for supporting this access control method?
#Ethernet and Star
12
What is the best way to fully ensure that data is unable to be recovered from a hard drive?
#shattering the hard drive platters with a hammer
13
A technician is asked to configure the time the system must be idle before the hard disk spins down on all the Windows-based laptops in the company. The technician configured the power options in Windows but it appears to have no effect. Where should the technician look to enable power management?
#System Registry
14
A printer has a paper jam. An impatient user has sent multiple print jobs of the same document to this printer. What can be done to remove these print jobs?
#Cancel the jobs in the printer queue.
15
ABC Inc. decided to integrate redundancy by connecting multiple hard disks to duplicate the information they store. Which type of adapter will need to be installed on the servers to accomplish the desired redundancy?
#RAID adapter
16
A call center technician has asked a customer to perform a simple operation to fix a problem on a computer. The customer seems unable to perform the task. What should the technician do?
#Determine whether the customer would prefer to receive the instructions in another form, such as e-mailed, illustrated written instructions.
17
Which two technologies enable printers to be accessed by multiple network users? (Choose two.)
#Wi-Fi
#Ethernet
18
A user reports that a printer is printing unknown characters on documents. What is a possible solution to this issue?
#Uninstall and reinstall the printer driver.
19
Which network device uses a MAC address table to segment the network?
#router
20
A technician needs to configure the hard drive on a computer so that there appears to be one drive for the operating system and four drives for data from different applications. How can the hard drive be configured to provide this perception?
#Create one primary partition and one logical partition with four logical drives within it.
21
A supervisor received a complaint that one of the technicians was rude and disrespectful. Which action by the technician most likely caused the customer to complain?
#The technician interrupted a number of times to ask questions.
22
A technician is troubleshooting a user complaint that a printer is not printing a report. Which step is one of the first that the technician should take?
#Check the Device Manager on the user computer for hardware problems.
23
Which Registry file contains information about all software that is installed on a Windows XP computer?
#HKEY_LOCAL_MACHINE
24
A hacker is detected using commonly available wireless hacking tools to access encrypted wireless network communication. Which resolution would prevent this action?
#Change the SSID that is being used on the wireless network.
25
Which two general precautions should be taken before replacing any non-hot-swappable laptop component? (Choose two.)
#Disconnect the power cord.
#Remove any batteries.
26
Which power mode should be used by a laptop so that all the data is saved, all the applications the user was working on are left open, and there is no power used by the laptop?
#Hibernate
27
What is the purpose of SCSI and RAID adapters?
#to connect storage devices such as hard disk drives to a PC
28
Which network protocol is used to automatically assign an IP address to a computer on a network?
#DHCP
29
A customer used the convert.exe utility to take advantage of NTFS security features. The customer later discovered that the application on the computer can only read FAT32 files. After the hard drive was formatted back to FAT32, the customer noticed all of the data files are missing. What should the customer do next?
#Restore the data files that were backed up in preparation for the conversion.
30
Which two components normally require a laptop to be powered down and the battery removed before removing the components? (Choose two.)
#internal hard drive
#RAM
31
A customer reports that after using a computer for over a year, the computer now takes more time to access the files. Which management tool can be used first, before any other complex procedure?
#defrag
32
A customer needs to purchase a new power supply for a computer. What must be considered when selecting an appropriate power supply?
#The power supply has sufficient wattage to support all components inside the computer.
33
What is a benefit of using the USB or FireWire ports to connect peripherals to a laptop?
#The peripherals can be plugged in and out without turning the laptop off.
34
A small business has used a high quality configurable flatbed scanner to scan a number of photographs to print as large posters. However, the quality of the images printed as posters is poor. What should the user do?
#Increase the resolution of the scanner.
35
A user has been writing data to a USB flash memory drive. What should the user do before removing the device?
#Click on the Safely Remove Hardware icon in the system tray then on the device.
36
A technician installed a network adapter in a computer and wants to test network connectivity. The ping command can only receive a response from local workstations. What could be causing the problem?
#The default gateway is not set.
37
A technician is explaining the differences between inkjet printers and laser printers to a customer. Which two comparisons should the technician make? (Choose two.)
#Inkjet printers are less expensive than laser printers.
#The laser printer output is dry after printing, but an inkjet printer may still have wet ink on the paper after printing.
38
A network administrator is troubleshooting a server that keeps crashing. While monitoring traffic to the server, the administrator notices repeated, larger than normal pings to the server. What is the name of this type of attack?
#ping of death
39
A technician wants to create a new partition on a new additional hard drive. Which tool should be used?
#Disk Management
40
Which two quick solutions are commonly recommended when a technician is troubleshooting a laptop? (Choose two.)
#Reboot the laptop.
#Disconnect the peripherals.
41
A company uses a single computer to receive and test all Windows updates. When the most recent update was installed, several programs failed. What is the first course of action that a technician should attempt to remove the update?
#Run a System Restore from the last restore point.
42
A mobile training room uses a generator to power the PCs, servers, and printers. The company that runs the room upgraded the equipment but then found that when all the devices are powered up they become unreliable, with some PCs shutting down. What may cause this power problem?
#The power consumption of all devices is too much for the electrical circuit that is provided.
43
When installing the Windows XP operating system, a technician is given a choice of file systems to use. If security is a requirement, which file system should be chosen?
#NTFS
44
A technician has replaced a failing floppy drive. While testing the new drive, the technician notices that the floppy drive light remains lit constantly. What is most likely the cause of the problem?
#The ribbon cable is installed incorrectly.
45
Which two types of connectors can be found on DVI cables? (Choose two.)
46
Which Windows tool should be run before upgrading the operating system?
#Ntbackup
47
The technician has been asked to upgrade the printer driver for an old printer. What is the best source for a new driver?
#manufacturer's website
48
Where can a user change the idle time after which a laptop will switch to standby mode?
#Left-click Start > Control Panel > Power Options, then click the Power Schemes tab.
49
A home computer owner has a PC system that runs Windows XP. For security reasons the owner has been using a limited local user account for a number of years. The owner wishes to install a new piece of software, but the user account does not have the necessary permissions. Which type of account does the owner need to use to install the new software?
#administrator
50
A student enables file sharing on a laptop so that a friend can access music files. Which type of service is being configured?
#peer-to-peer
51
What do the terms refresh rate, interlace, and aspect ratio explain?
#image properties of a monitor
52
A technician wishes to boot a computer using a CD-ROM that contains a limited operating system and diagnostic utilities. Where would the technician set the boot order for the PC?
#BIOS
Rabu, 08 Desember 2010
Diposkan oleh sukri di 21:14
1
A computer user buys a low priced replacement monitor but finds that there is a lot of flicker. The flicker makes the monitor unusable. Which characteristic of a monitor needs to be considered to ensure flicker-free viewing?
#refresh rate
2
When analyzing a protocol used on the network, it is discovered that multicast messages are being sent to network devices. Which class of IP addressing is being used to send these messages?
#D
3
A technician notices that a data floppy disk is in the floppy disk drive of a computer when it is powered on. Which error message could this potentially cause?
#invalid system disk
4
What characterizes spoofing?
#Making data appear to come from a source other than the actual source.
5
When a Windows XP computer has completed the POST for each adapter card that has a BIOS, what is the next step during the boot sequence?
#BIOS reads the MBR.
6
When calculating the total cost of ownership of a printer it is necessary to consider the cost of the consumables. Which two consumables are associated with an inkjet printer? (Choose two.)
#ink cartridge
#paper
7
Which protocol adds security to remote connections?
#SSH
8
What is the purpose of an IRQ?
#Request information from the CPU.
9
A wireless LAN is being deployed inside the new park ranger, one room office that is located at the highest part of the national park. When the testing was completed, the technicians reported that occasionally, the wireless LAN signal is affected by some type of interference. What are two possible causes of the signal distortion? (Choose two.)
#the number of wireless devices that are used in the wireless LAN
#the large number of trees that surround the office
10
When installing a service pack or security patches on an operating system, what should be done to protect the system in the event of a faulty or aborted installation?
#Create a restore point.
11
A technician is asked to wire a network that supports CSMA/CD. Which architecture and physical topology should the technician use for supporting this access control method?
#Ethernet and Star
12
What is the best way to fully ensure that data is unable to be recovered from a hard drive?
#shattering the hard drive platters with a hammer
13
A technician is asked to configure the time the system must be idle before the hard disk spins down on all the Windows-based laptops in the company. The technician configured the power options in Windows but it appears to have no effect. Where should the technician look to enable power management?
#System Registry
14
A printer has a paper jam. An impatient user has sent multiple print jobs of the same document to this printer. What can be done to remove these print jobs?
#Cancel the jobs in the printer queue.
15
ABC Inc. decided to integrate redundancy by connecting multiple hard disks to duplicate the information they store. Which type of adapter will need to be installed on the servers to accomplish the desired redundancy?
#RAID adapter
16
A call center technician has asked a customer to perform a simple operation to fix a problem on a computer. The customer seems unable to perform the task. What should the technician do?
#Determine whether the customer would prefer to receive the instructions in another form, such as e-mailed, illustrated written instructions.
17
Which two technologies enable printers to be accessed by multiple network users? (Choose two.)
#Wi-Fi
#Ethernet
18
A user reports that a printer is printing unknown characters on documents. What is a possible solution to this issue?
#Uninstall and reinstall the printer driver.
19
Which network device uses a MAC address table to segment the network?
#router
20
A technician needs to configure the hard drive on a computer so that there appears to be one drive for the operating system and four drives for data from different applications. How can the hard drive be configured to provide this perception?
#Create one primary partition and one logical partition with four logical drives within it.
21
A supervisor received a complaint that one of the technicians was rude and disrespectful. Which action by the technician most likely caused the customer to complain?
#The technician interrupted a number of times to ask questions.
22
A technician is troubleshooting a user complaint that a printer is not printing a report. Which step is one of the first that the technician should take?
#Check the Device Manager on the user computer for hardware problems.
23
Which Registry file contains information about all software that is installed on a Windows XP computer?
#HKEY_LOCAL_MACHINE
24
A hacker is detected using commonly available wireless hacking tools to access encrypted wireless network communication. Which resolution would prevent this action?
#Change the SSID that is being used on the wireless network.
25
Which two general precautions should be taken before replacing any non-hot-swappable laptop component? (Choose two.)
#Disconnect the power cord.
#Remove any batteries.
26
Which power mode should be used by a laptop so that all the data is saved, all the applications the user was working on are left open, and there is no power used by the laptop?
#Hibernate
27
What is the purpose of SCSI and RAID adapters?
#to connect storage devices such as hard disk drives to a PC
28
Which network protocol is used to automatically assign an IP address to a computer on a network?
#DHCP
29
A customer used the convert.exe utility to take advantage of NTFS security features. The customer later discovered that the application on the computer can only read FAT32 files. After the hard drive was formatted back to FAT32, the customer noticed all of the data files are missing. What should the customer do next?
#Restore the data files that were backed up in preparation for the conversion.
30
Which two components normally require a laptop to be powered down and the battery removed before removing the components? (Choose two.)
#internal hard drive
#RAM
31
A customer reports that after using a computer for over a year, the computer now takes more time to access the files. Which management tool can be used first, before any other complex procedure?
#defrag
32
A customer needs to purchase a new power supply for a computer. What must be considered when selecting an appropriate power supply?
#The power supply has sufficient wattage to support all components inside the computer.
33
What is a benefit of using the USB or FireWire ports to connect peripherals to a laptop?
#The peripherals can be plugged in and out without turning the laptop off.
34
A small business has used a high quality configurable flatbed scanner to scan a number of photographs to print as large posters. However, the quality of the images printed as posters is poor. What should the user do?
#Increase the resolution of the scanner.
35
A user has been writing data to a USB flash memory drive. What should the user do before removing the device?
#Click on the Safely Remove Hardware icon in the system tray then on the device.
36
A technician installed a network adapter in a computer and wants to test network connectivity. The ping command can only receive a response from local workstations. What could be causing the problem?
#The default gateway is not set.
37
A technician is explaining the differences between inkjet printers and laser printers to a customer. Which two comparisons should the technician make? (Choose two.)
#Inkjet printers are less expensive than laser printers.
#The laser printer output is dry after printing, but an inkjet printer may still have wet ink on the paper after printing.
38
A network administrator is troubleshooting a server that keeps crashing. While monitoring traffic to the server, the administrator notices repeated, larger than normal pings to the server. What is the name of this type of attack?
#ping of death
39
A technician wants to create a new partition on a new additional hard drive. Which tool should be used?
#Disk Management
40
Which two quick solutions are commonly recommended when a technician is troubleshooting a laptop? (Choose two.)
#Reboot the laptop.
#Disconnect the peripherals.
41
A company uses a single computer to receive and test all Windows updates. When the most recent update was installed, several programs failed. What is the first course of action that a technician should attempt to remove the update?
#Run a System Restore from the last restore point.
42
A mobile training room uses a generator to power the PCs, servers, and printers. The company that runs the room upgraded the equipment but then found that when all the devices are powered up they become unreliable, with some PCs shutting down. What may cause this power problem?
#The power consumption of all devices is too much for the electrical circuit that is provided.
43
When installing the Windows XP operating system, a technician is given a choice of file systems to use. If security is a requirement, which file system should be chosen?
#NTFS
44
A technician has replaced a failing floppy drive. While testing the new drive, the technician notices that the floppy drive light remains lit constantly. What is most likely the cause of the problem?
#The ribbon cable is installed incorrectly.
45
Which two types of connectors can be found on DVI cables? (Choose two.)
46
Which Windows tool should be run before upgrading the operating system?
#Ntbackup
47
The technician has been asked to upgrade the printer driver for an old printer. What is the best source for a new driver?
#manufacturer's website
48
Where can a user change the idle time after which a laptop will switch to standby mode?
#Left-click Start > Control Panel > Power Options, then click the Power Schemes tab.
49
A home computer owner has a PC system that runs Windows XP. For security reasons the owner has been using a limited local user account for a number of years. The owner wishes to install a new piece of software, but the user account does not have the necessary permissions. Which type of account does the owner need to use to install the new software?
#administrator
50
A student enables file sharing on a laptop so that a friend can access music files. Which type of service is being configured?
#peer-to-peer
51
What do the terms refresh rate, interlace, and aspect ratio explain?
#image properties of a monitor
52
A technician wishes to boot a computer using a CD-ROM that contains a limited operating system and diagnostic utilities. Where would the technician set the boot order for the PC?
#BIOS
A computer user buys a low priced replacement monitor but finds that there is a lot of flicker. The flicker makes the monitor unusable. Which characteristic of a monitor needs to be considered to ensure flicker-free viewing?
#refresh rate
2
When analyzing a protocol used on the network, it is discovered that multicast messages are being sent to network devices. Which class of IP addressing is being used to send these messages?
#D
3
A technician notices that a data floppy disk is in the floppy disk drive of a computer when it is powered on. Which error message could this potentially cause?
#invalid system disk
4
What characterizes spoofing?
#Making data appear to come from a source other than the actual source.
5
When a Windows XP computer has completed the POST for each adapter card that has a BIOS, what is the next step during the boot sequence?
#BIOS reads the MBR.
6
When calculating the total cost of ownership of a printer it is necessary to consider the cost of the consumables. Which two consumables are associated with an inkjet printer? (Choose two.)
#ink cartridge
#paper
7
Which protocol adds security to remote connections?
#SSH
8
What is the purpose of an IRQ?
#Request information from the CPU.
9
A wireless LAN is being deployed inside the new park ranger, one room office that is located at the highest part of the national park. When the testing was completed, the technicians reported that occasionally, the wireless LAN signal is affected by some type of interference. What are two possible causes of the signal distortion? (Choose two.)
#the number of wireless devices that are used in the wireless LAN
#the large number of trees that surround the office
10
When installing a service pack or security patches on an operating system, what should be done to protect the system in the event of a faulty or aborted installation?
#Create a restore point.
11
A technician is asked to wire a network that supports CSMA/CD. Which architecture and physical topology should the technician use for supporting this access control method?
#Ethernet and Star
12
What is the best way to fully ensure that data is unable to be recovered from a hard drive?
#shattering the hard drive platters with a hammer
13
A technician is asked to configure the time the system must be idle before the hard disk spins down on all the Windows-based laptops in the company. The technician configured the power options in Windows but it appears to have no effect. Where should the technician look to enable power management?
#System Registry
14
A printer has a paper jam. An impatient user has sent multiple print jobs of the same document to this printer. What can be done to remove these print jobs?
#Cancel the jobs in the printer queue.
15
ABC Inc. decided to integrate redundancy by connecting multiple hard disks to duplicate the information they store. Which type of adapter will need to be installed on the servers to accomplish the desired redundancy?
#RAID adapter
16
A call center technician has asked a customer to perform a simple operation to fix a problem on a computer. The customer seems unable to perform the task. What should the technician do?
#Determine whether the customer would prefer to receive the instructions in another form, such as e-mailed, illustrated written instructions.
17
Which two technologies enable printers to be accessed by multiple network users? (Choose two.)
#Wi-Fi
#Ethernet
18
A user reports that a printer is printing unknown characters on documents. What is a possible solution to this issue?
#Uninstall and reinstall the printer driver.
19
Which network device uses a MAC address table to segment the network?
#router
20
A technician needs to configure the hard drive on a computer so that there appears to be one drive for the operating system and four drives for data from different applications. How can the hard drive be configured to provide this perception?
#Create one primary partition and one logical partition with four logical drives within it.
21
A supervisor received a complaint that one of the technicians was rude and disrespectful. Which action by the technician most likely caused the customer to complain?
#The technician interrupted a number of times to ask questions.
22
A technician is troubleshooting a user complaint that a printer is not printing a report. Which step is one of the first that the technician should take?
#Check the Device Manager on the user computer for hardware problems.
23
Which Registry file contains information about all software that is installed on a Windows XP computer?
#HKEY_LOCAL_MACHINE
24
A hacker is detected using commonly available wireless hacking tools to access encrypted wireless network communication. Which resolution would prevent this action?
#Change the SSID that is being used on the wireless network.
25
Which two general precautions should be taken before replacing any non-hot-swappable laptop component? (Choose two.)
#Disconnect the power cord.
#Remove any batteries.
26
Which power mode should be used by a laptop so that all the data is saved, all the applications the user was working on are left open, and there is no power used by the laptop?
#Hibernate
27
What is the purpose of SCSI and RAID adapters?
#to connect storage devices such as hard disk drives to a PC
28
Which network protocol is used to automatically assign an IP address to a computer on a network?
#DHCP
29
A customer used the convert.exe utility to take advantage of NTFS security features. The customer later discovered that the application on the computer can only read FAT32 files. After the hard drive was formatted back to FAT32, the customer noticed all of the data files are missing. What should the customer do next?
#Restore the data files that were backed up in preparation for the conversion.
30
Which two components normally require a laptop to be powered down and the battery removed before removing the components? (Choose two.)
#internal hard drive
#RAM
31
A customer reports that after using a computer for over a year, the computer now takes more time to access the files. Which management tool can be used first, before any other complex procedure?
#defrag
32
A customer needs to purchase a new power supply for a computer. What must be considered when selecting an appropriate power supply?
#The power supply has sufficient wattage to support all components inside the computer.
33
What is a benefit of using the USB or FireWire ports to connect peripherals to a laptop?
#The peripherals can be plugged in and out without turning the laptop off.
34
A small business has used a high quality configurable flatbed scanner to scan a number of photographs to print as large posters. However, the quality of the images printed as posters is poor. What should the user do?
#Increase the resolution of the scanner.
35
A user has been writing data to a USB flash memory drive. What should the user do before removing the device?
#Click on the Safely Remove Hardware icon in the system tray then on the device.
36
A technician installed a network adapter in a computer and wants to test network connectivity. The ping command can only receive a response from local workstations. What could be causing the problem?
#The default gateway is not set.
37
A technician is explaining the differences between inkjet printers and laser printers to a customer. Which two comparisons should the technician make? (Choose two.)
#Inkjet printers are less expensive than laser printers.
#The laser printer output is dry after printing, but an inkjet printer may still have wet ink on the paper after printing.
38
A network administrator is troubleshooting a server that keeps crashing. While monitoring traffic to the server, the administrator notices repeated, larger than normal pings to the server. What is the name of this type of attack?
#ping of death
39
A technician wants to create a new partition on a new additional hard drive. Which tool should be used?
#Disk Management
40
Which two quick solutions are commonly recommended when a technician is troubleshooting a laptop? (Choose two.)
#Reboot the laptop.
#Disconnect the peripherals.
41
A company uses a single computer to receive and test all Windows updates. When the most recent update was installed, several programs failed. What is the first course of action that a technician should attempt to remove the update?
#Run a System Restore from the last restore point.
42
A mobile training room uses a generator to power the PCs, servers, and printers. The company that runs the room upgraded the equipment but then found that when all the devices are powered up they become unreliable, with some PCs shutting down. What may cause this power problem?
#The power consumption of all devices is too much for the electrical circuit that is provided.
43
When installing the Windows XP operating system, a technician is given a choice of file systems to use. If security is a requirement, which file system should be chosen?
#NTFS
44
A technician has replaced a failing floppy drive. While testing the new drive, the technician notices that the floppy drive light remains lit constantly. What is most likely the cause of the problem?
#The ribbon cable is installed incorrectly.
45
Which two types of connectors can be found on DVI cables? (Choose two.)
46
Which Windows tool should be run before upgrading the operating system?
#Ntbackup
47
The technician has been asked to upgrade the printer driver for an old printer. What is the best source for a new driver?
#manufacturer's website
48
Where can a user change the idle time after which a laptop will switch to standby mode?
#Left-click Start > Control Panel > Power Options, then click the Power Schemes tab.
49
A home computer owner has a PC system that runs Windows XP. For security reasons the owner has been using a limited local user account for a number of years. The owner wishes to install a new piece of software, but the user account does not have the necessary permissions. Which type of account does the owner need to use to install the new software?
#administrator
50
A student enables file sharing on a laptop so that a friend can access music files. Which type of service is being configured?
#peer-to-peer
51
What do the terms refresh rate, interlace, and aspect ratio explain?
#image properties of a monitor
52
A technician wishes to boot a computer using a CD-ROM that contains a limited operating system and diagnostic utilities. Where would the technician set the boot order for the PC?
#BIOS
for a branch office located in a new metropolitan office building. Which
connection would provide the highest bandwidth and reliability at the lowest cost?
DSL
ISDN
satellite
wireless
ISDN
satellite
wireless
2 points for Option 1
Max Value = 2
17. A new technician has joined the IT team and is about to service a heavy
printer. Which two precautions should be taken to avoid any injury when
transporting the heavy printer to the service area? (Choose two.)
Avoid lifting the equipment using the strength in your back.
Lift the equipment using the strength in your legs and knees.
Avoid bending your knees when lifting the printer.
Bend your back to pick the printer up.
Avoid lifting the printer close to your body.
Avoid lifting the equipment using the strength in your back.
Lift the equipment using the strength in your legs and knees.
Avoid bending your knees when lifting the printer.
Bend your back to pick the printer up.
Avoid lifting the printer close to your body.
Option 1 and Option 2 are correct.
Max Value = 2
18. What are two characteristics of the IEEE 1284 standard? (Choose two.)
These cables usually have 9 pins or 25 pins on both ends.
The maximum cable length is 50 ft (15 m).
All ports used by this standard are also known as D-shell ports.
The two available operative modes are EPP and ECP.
Bi-directional communication is allowed.
These cables usually have 9 pins or 25 pins on both ends.
The maximum cable length is 50 ft (15 m).
All ports used by this standard are also known as D-shell ports.
The two available operative modes are EPP and ECP.
Bi-directional communication is allowed.
Option 4 and Option 5 are correct.
Max Value = 2
19. Which type of printer configuration method overrides any other type of
configuration?
default
global
predefined
per-document
global
predefined
per-document
2 points for Option 4
Max Value = 2
20. After scanning an image, what is the next step to conclude a scanner test?
Scan the same image again and compare both scanned images to detect scanning
deficiencies.
Calibrate the scanner based on the image that has been scanned.
Print the scanned image and contrast it with the scanned image.
Visually compare the image against the image on the screen.
Calibrate the scanner based on the image that has been scanned.
Print the scanned image and contrast it with the scanned image.
Visually compare the image against the image on the screen.
2 points for Option 4
Max Value = 2
21. Which three laser printer components usually break? (Choose three.)
fuser assembly
primary corona
pickup rollers
transfer rollers
secondary corona
paper trays
fuser assembly
primary corona
pickup rollers
transfer rollers
secondary corona
paper trays
Option 1, Option 3, and Option 4 are correct.
Max Value = 3
22. After gathering information from a user regarding failure of a printer, which
three actions should be performed? (Choose three.)
Change the communication cable.
Ensure all cables are connected correctly.
Change the communication cable.
Ensure all cables are connected correctly.
Tidak ada komentar:
Posting Komentar